Converter Heavy Duty

BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100


BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100
BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100
BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100
BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100

BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100  BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100

Bob's Machine Shop's manual jack plates are our lightest and cheapest jack plate option! Bob's Machine Shop's convertable manual MJ5 jack plate is actually 4 units in one! It can be 2.5" setback or 5" setback. And it can have a straight or negative 6 degree wedge.

They are anodized black for race oriented looks. Easy adjustments are made on the side of the jack plate.

2 1/2 inch offset no wedge A feature which is used on the lightest of boats. Allowing the engine to be raised to its maximum height without putting the weight of the engine too far behind the transom which could create too much bow lift. 2 1/2 inch Offset with Negative 6-Degree Wedge This design can be used when the transom of a boat is too steep of an angle to allow the outboard motor to perform properly. For example: an 18-degree transom when this design is applied. 5-inch Offset No Wedge This option desirability will vary from one boat to another depending upon weight and length of boat.

Some outboard motors have a limited trim angle and the 6-degree wedge may not allow for enough bow lift. By setting the plate at the no wedge design, it will give maximum bow lift. 5-inch Offset with 6-Degree Wedge.

Jacking bolts - allow motor to be moved to any height. No need to take boat out of the water. Offset - positions motor 5 1/2 inches behind transom. This allows prop to run in cleaner water, away from the turbulence and bubbles created by the hull. This helps stop slippage of prop, and helps stop torque in steering wheel at high speeds. Trim-In - this allows motor to be trimmed in or down 6 degrees more than if mounted flat on transom. Helps stop low speed porpoising. Constructed of aircraft grade aluminum and stainless steel. Anodized - anodized black finish to prevent corrosion. Anodize also lets paint stick to aluminum if painting is preferred.

Narrow designed - only inches wide, make this plate possible to fit the narrowest of transoms. Fits V-6 - pre-drilled to fit all late model V-6's. Can be modified to fit any size outboard.

Converting the new 4 in 1 is as easy as dropping anchor! Adjustable plates turn 180 degrees and switch sides, then bolt in place. Overall width: 17-7/8(45.3cm). Overall height :14(35.5cm).

All manual jac plates have 2 1/2"(6.3cm) of lift built in and 4"(10.1cm) of adjustable lift. Made in USA, in our own factory in Tampa, Florida. Rated for 300HP, upto 625 lbs motors (heavier should use Extreme series).

Dimensions: 18 x 11 x 7 in. The item "BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100" is in sale since Tuesday, November 10, 2020. This item is in the category "eBay Motors\Parts & Accessories\Boat Parts\Outboard Engines & Components\Other". The seller is "pwc_parts" and is located in Essex, Maryland.

This item can be shipped worldwide.

  1. Brand: BOB'S MACHINE SHOP
  2. Manufacturer Part Number: 100-205100
  3. Bundle Description: No
  4. Modified Item: No
  5. California Prop 65 Warning: No


BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100  BMS Convertable MJ5 Heavy Duty Manual Jack Plate 300 HP Max 100-205100